A rear axle bearing puller is a tool used to remove the bearing from the rear wheels of a vehicle. This tool is important for use when you need to replace the bearing or perform other maintenance on the rear wheels. There are two parts of the bearing puller: the handle and the jaws. The handle is attached to the jaws, which are inserted into the bearing. These jaws are used to pull out the bearing.
VEVOR’s rear axle bearing puller helps remove bearings from a vehicle’s rear wheels. These bearing pullers are necessary when you have to do the maintenance and repair on the rear wheels. They can easily remove the bearings without causing any damage.
Top 5 Rear Axle Bearing Puller
There are different types of rear axle bearing pullers, but in this guide, we will introduce you to the top 5 VEVOR rear axle bearing pullers, and these are as follows:
1- Rear Axle Shaft Bearing Puller
Features and Performance
Material Used
The material used in this rear axle shaft bearing puller is made of premium material, which is strong, which makes it highly durable and can be used for the long term.
Use
The rear axle shaft bearing puller is very easy to use. You do not need a hammer, chisel, or torch along to use it. You can easily use it on its own.
Save the ABS
The rear axle bearing puller saves the ABS sensor ring and removes the bearing from the axle.
Compatibility
These rear axle shaft bearing puller is very compatible. Most Nissan, Mitsubishi, and Isuzu models have the backing plate.
Pros
●They are widely used.
●Easy to handle.
2- Upper Bearing Carrier Puller
Features and Performance
Material Used
The material used in the making of the upper bearing carrier puller is of high quality, which makes it durable. It is made up of steel and provides good performance. The material makes it corrosion and abrasion free which increase its durability.
Compatibility
This bearing puller is compatible with Yamaha, Johnson, Evinrude, Honda, and Mercury. In the upper bearing carrier puller, the power is equally distributed, which helps remove the bearing carrier easily without causing any damage to your bearing liner.
Working Efficiency
This bearing puller has high working efficiency which reduces dismantling time along with removing the upper bearing carrier with less damage. It can not pry into seal surfaces as well.
Jaws and Collar Adapter
There is a cylindrical casing that is designed for pushing and pulling back.
●The adjustable jaws make them be used on various-sized outboards.
●The shaft collars can be removed quickly with the help of a drive shaft collar adapter.
Pros
●They can be easily installed.
●No need for complex assembly tools.
3- Carrier & Pinion Bearing Puller
Features and Performance
Material Used
The carrier and pinion bearing puller is made up of steel, which provides strong and durable performance. They are resistant to corrosion, abrasion, and impact. The material used in the making of this bearing puller makes it durable for a long time.
Easy use
You do not need other complex working tools. You can remove the bearing b placing the main body over the plug. You need to adjust the lower and upper adjusting rings and select a proper clamshell and tighten the retaining ring.
Compatibility
This bearing puller is compatible with Dana 30, 40, 60, and 70, For 10.25″ bearings. The power of this bearing puller is equally distributed, which removes the bearings quickly without any damage.
Working efficiency
These bearing pullers are efficient in work as they remove the bearing with no time and without any effort. It can also reduce the dismantling time.
Pros
●There is a main puller’s body, plug, center bolt, three clamshells, retaining ring, and adjuster rings.
●Comes with a handy stand.
4- Lower Bearing Carrier Puller
Features and Performance
Material Used
Steel material is used in the making of lower-bearing carrier pullers. They are strong and durable. They can easily withstand abrasion and corrosion.
Compatibility
These bearing pullers are compatible with Yamaha, Johnson, Evinrude, Honda, and Mercury. They are good in performance and can quickly remove the bearing carrier with less damage to your bearing liner.
Swinging Arms and Bearing Head
These bearing pullers have adjustable swinging arms that can quickly pivot. It had a bearing head which allowed for zero friction and improved the pulling power.
Screw-rod
The heavy-duty screw rod is made to pull out the lower bearing carrier quickly.
Installation
The installation is easy as you do not need other complex assembly tools. The process is labor-saving as all you have to do is insert the screw rod into the groove hole, then fix the arms on both sides of the groove. Adjust the swing arms to fit the gear case, and it is ready to use.
Pros
●They have high working efficiency.
●Reduces dismantle time
●Does not pry into the sealing surface.
5- Front Wheel Drive Bearing Adapters Puller
Features and Performance
Compatibility
Front-wheel drive bearing adapters pullers are compatible with all front-wheel-drive cars and light trucks. They do not need a front-end alignment as they can replace the bearings while keeping the steering knuckle and strut assembly intact.
All in one
The front wheel drive bearing adapters puller has the following:
●Four sleeves
●Two sleeve plates
●13 bushings
●One washer
●Two sliding screws
●One spacer
●One plate
●1 sliding nut
Installation
The installation of this bearing puller is very easy. All you have to do is to identify the correct sleeve cap to sit on the bearing housing.
Reliability
HRC25 to HRC35 hardness ensures the ability of the front wheel drive bearing adapters puller. They can withstand the extreme level of fastener and are resistant to rust. They are constructed from 45# steel with a protective black-oxide finish.
Pros
●Each socket has a designated slot.
●The portable carrying case is for easy storage.
Different types of Rear Axle Bearing Puller
Different types of rear axle bearing pullers are widely used in the maintenance and repair of the bearing. Some of the widely used types of rear axle bearing pullers are given below:
●Orion Motor Tech Rear Axle Bearing Puller Tool Set
●The ECOTRIC Rear Wheel Axle Bearing Puller and ABS Tone Ring
●8MILELAKE 9 Way Slide Hammer Puller Axle Front Rear Wheel Bearing Dent Hub Gear Puller Remover Set
●Orion Motor Tech 9-Way Slide Hammer Puller Set, Front Wheel Hub Bearing Remover & Rear Wheel Axle Hub Dent Shaft Puller Tool Kit
What should you look for when buying a Rear Axle Bearing Puller?
There are different types of rear axle bearing pullers available in the market, but it is very important to choose which bearing puller will be the best for your vehicle. Some pullers are universal and can work on almost any vehicle, but some are specific and work only on a certain type of vehicle. These pullers are designed for specific types of vehicles. There are different sizes and styles available; you can find any according to your requirements.
There are some things you need to know that will make it easier for you to buy a rear axle bearing puller, and these are as follow:
Comfortable to use
Buy a rear axle bearing puller that is easy to operate and comfortable to use.
Capacity and Compatibility
You need to consider its capacity and compatibility with your vehicle.
Type
Two types of pullers are hydraulic pullers and mechanical pullers. Both are effective and easy to use. But hydraulic pullers tend to be more powerful than mechanical pullers.
Reviews
Don’t forget to read the reviews before buying the bearing puller, as you can be well aware of its pros and cons from the reviews.
Are Rear Axle Bearing Pullers worth it?
The rear axle bearing puller is designed to remove the bearings from the hub of the vehicle’s rear wheel. Buying a rear axle bearing puller is worth it, as it is a necessary tool to replace the bearings. The process of replacing the bearing with the rear axle bearing puller is much easier and simpler.
VEVOR Rear axle bearing puller is a must-buy as they have many benefits, and these are as follow:
●It can easily remove the bearing with less labor and less time.
●The removal is much easier and quicker.
●It protects the bearings from damage.
●It makes sure that the bearing is removed smoothly and evenly.
●It prevents all the problems while reinstallation.
FAQs about Rear Axle Bearing Puller
Q: Are they durable?
A: Yes, the material used in the making of rear axle bearing pullers is strong and makes them durable.
Q: How to install rear-axle bearing puller?
A: The installation of each bearing puller is different depending on the type you are buying. But the installation of every rear axle bearing puller is easy.
Q: Are they corrosion-resistant?
A: Yes, they are abrasion and corrosion-resistant.
