Reviews for VEVOR Milling Machine Work Table Slide Milling Working Cross Table Machine Compound Slide Milling TablePrecision Milling Cross Worktable (7.3 x 4 Inch)

The P man

Worth every penny

I was impressed by the packaging, and overall quality of this table. I have a 20", 2hp craftsman drill press, ended up mounting this sideways on the table. The y Axis hand wheel clears the table this way. Could only use the rear mounting holes, may drill and tap the front holes into the table later. But, the 2 mounting holes has it down flat and sturdy enough that I may not bother. Didn't take this apart, just lubed everything, adjusted the tension on the x Axis lead screw lock nuts. Actually bought this from a different site, wasn't able to leave a review, so did that here.

See More See Less

Helpful Sending feedback... Thank you for your feedback. 1 people found this helpful

Kier

Good For The Price

Overall great for the price. I’ve got it set up on my 35 year old drill press with a pair of 4 inch vises on top, working well so far. 7/16 T-slot nuts do fit but…. Not perfectly. I had to add washers under the corners of the vises because the slots aren’t quite tight enough and the T-slot nuts can come up too far. But with that modification it’s working great.If you can keep the little guide/tension bars in between the decks in place it stays pretty accurate, honestly impressed by that. They have a habit of walking back and forth though and if you aren’t careful can introduce some play.The casting work is pretty poor, honestly, a lot of weird spots and voids and just messy stuff, but for the price I expected that so I’m not disappointed. It gives more travel than anything else at this price and it’s very solid so I’m not worried about damaging it.Bottom line, I’d recommend this if you’re looking for a budget cross table.

See More See Less

Helpful Sending feedback... Thank you for your feedback. 1 people found this helpful

javier

The cast is a little rough and have a little backlash nothing mayor

Overall I like it for what I needed fits perfectly on a WEN 12 inches with 6 inches vise on top can't get better for $170.00 fast delivery and no broken/missing parts and for DIY go for it is perfect

See More See Less

Helpful Sending feedback... Thank you for your feedback. 1 people found this helpful

Dan the man

Quality tool and great price

Reviews on this table say to disassemble, clean, and deburr. You do not have to do this. Wipe your milling table down with WD40 or fuel oil, good enough, anything else will result in a block of rusty metal and trouble. Lubricate weighs with non detergent oil. Adjust weighs enough to take out slop. After bolting to machine you are ready to go. Love the price and the closed table which allows for flood cooling with little modification.

See More See Less

Helpful Sending feedback... Thank you for your feedback. 1 people found this helpful

Jcloran

Exceeded my expectations!

This thing is massive and amazing!

See More See Less

Helpful Sending feedback... Thank you for your feedback. 0 people found this helpful

K.C. Bass

Solid, well built and surprisingly accurate.

Works well for gunsmithing. It is very heavy built. I will likely add digital readout soon.

See More See Less

Helpful Sending feedback... Thank you for your feedback. 0 people found this helpful

jeff

4 Hours of hand work required

First, I needed to completely disassemble and clean crud from all surfaces. cleaned all threads; honed ways, dovetails and gibs (which also spent the night in Evapo-Rust); lubricated all moving parts; adjusted the preload on the thrust bearings; reassembled and adjusted gibs. Now it works very smoothly and as accurately as I expected. This product is a beast and is worth the money if you have the time to work on it before use.Problems I encountered beyond the above: one of the 4 mounting holes apparently lost its sand during casting, so I had to drill it out, the hand wheels are very wobbly (but usable), and there was a lot of red paint on machined surfaces.

See More See Less

Helpful Sending feedback... Thank you for your feedback. 0 people found this helpful

Paul a Cote Sr

it works like i wanted it

works great ty for a great item .

See More See Less

Helpful Sending feedback... Thank you for your feedback. 0 people found this helpful

Richard Martinson

Works Pretty Well But....

I watched a review of a similar table from Vevor. but was not interested in spending the extra money so I purchased this one. I received this and completely disassembled the entire device. Cleaned the guides. Deburred all of the sharp edges and tuned up the bearing races as the jam nuts used to hold it all together are awful I mean not even concentric !!! After about 2 hours I was able to get this to work very well.Again it is an inexpensive table but with a little elbow grease and attention to detail it works good enough for my purposes. That being said it was a good purchase. I might swap out the acmes at a later date but for now it is fine.

See More See Less

Helpful Sending feedback... Thank you for your feedback. 0 people found this helpful

R. Chang

Works fine, esp for this price. Requires some prep work after receiving.

If you want a simple work table to use, especially for your drill press, this is a great table to consider and purchase. I found it to be accurate enough for what I am going to do with it. Is this something to use a professional machine shop and for cranking out a ton of parts? No -- but that should be apparent by the price point.The table requires some prep work once it arrives. This is what I did:1) Unwrapped and sprayed it down with brake cleaner to get all the nasty oil/grease off2) Disassembled the entire unit and sprayed it down again3) Took a wire brush to all the channels and guide areas to remove excess paint4) Sanded down the top deck to make sure it was truly flat5) Filed down all the spacers in the channel guides to remove any burrs6) Took a dremel with a sanding drum and knocked down all the edges7) Reassembled and greased the guides

See More See Less

Helpful Sending feedback... Thank you for your feedback. 0 people found this helpful

Customer Reviews for VEVOR Milling Machine Work Table Slide Milling Working Cross Table Machine Compound Slide Milling TablePrecision Milling Cross Worktable (7.3 x 4 Inch)

Customer Reviews

Ratings by Features

People Who Bought This Item Also Bought