Customer Reviews for VEVOR Plasma Cutter, 50Amp, Non-Touch Pilot Arc Air Cutting Machine with Torch, 110V/220V Dual Voltage AC IGBT Inverter Metal Cutting Equipment for 1/2" Clean Cut Aluminum and Stainless Steel, Black

Solid value here, comes with a lot of accessories -- air dryer attaches to the back and keeps everything nicely in order. Arcs without touching which is a nice luxury. Works good!

this machine is a small giant, I bought one to test it and now all my friends want one of these, the only thing that would change is the quality of the clamps

Great machine have enjoyed using it for my projects. I recommend the machine to friends. Great for hobbist.

Easy to use. Highly recommend, First thing we tried it on was 1/8" aluminum worked flawlessly cutting that and then a rusty floor. Have used a Hobart plasma torch to cut rusty floors. This machine is superior to the Hobart.

I went in with zero knowledge of how to use this machine. It had excellent directions everything hooked up easily. I definitely need more practice but can tell I will be using this alot. Had a buddy who uses these regularly check it out and he said it was a excellent machine. When I get better I will add more pictures.

It's tiny but this plasma cutter packs a punch! I ran this using a strait edge and it gives a nice clean strait cut. It's faster and cleaner than a torch and cleaning up the steel after the cut is less involved. Little to no slab build up and repairs/production time are speed up noticeably. It almost makes repairs fun.

Unit arrived on time and undamaged. Cutting a lot of 1/4" plate on 220volts and it does a nice job in the hands of this novice. It runs fine on 30A breakers. Some have commented about the ground clamp. I've had no issues with the clamp but the cable pulled out of the male connector on the other end. Set screw was tight but it didn't capture the cable well. I put a 6ga sleeve inside a 4ga sleeve and reinserted the cable. Now the set screw tightly grips the cable. Do not expect any further issues.

So far so good. I have cut a little bit of 1/2 inch stock without issue. Cots through lighter material like butter. Easy set up and operation.

Have not had a chance to use it yet but did put the filter together and attached to the back mounting point. One thing of note, the brass hose fittings that screw into the filter are soooooooo undersized for the threads that they screw into you have to use an ugly amount of Teflon tape and they still don't ever feel tight. I have not added pressure yet to see if I put enough tape on the threads to get a seal. I am hoping that once the snow melts, I will have some positive comments on its actual use, but so far it looks nice.

A very good quality home workshop plasma cutter. This plasma cutter can handle anything it is likely required to do in a home workshop. It would be limited for commercial or professional blacksmithing, but it is an excellent tool for home and hobby use. The product description is accurate. The tool includes everything needed except for a pressurized air supply (which is easily supplied by most home garage air compressors). Check the power supply available where you intend to use this cutter. It requires a 50 amp 110 Volt circuit, which is larger than most home circuits, or a 220 Volt circuit, which most homes do not have available as a readily accessible outdoor circuit. That said, those requirements can readily be met by installing the necessary circuit, which is a plus all the way around since many other tools can also benefit from this circuitry.The cuts it makes are clean, even for someone who does not use a plasma cutter regularly. The more you use it, the better you get at it. It can easily cut the metal found on most cars, which home craftsmen will likely need to cut. It works well for making silhouette cut-outs in most metals which are usually high-volume sales items at craft sales. It also works well for cutting silhouette targets for target shooting, especially for black powder enthusiasts. This is a good starter plasma cutter for someone wanting to explore the field and see if that is something they like to do because the cost is low enough to experiment with. Yet, it will handle most of the jobs you are likely to need it for at the home craftsman level. It is well made and will likely last a long time. I would definitely get it again.