Customer Reviews for VEVOR Paper Cutter, Guillotine Trimmer, 18" Cut Length, 20 Sheets Capacity, Heavy Duty Guillotine Paper Cutter with Guard Rail/Blade Lock for Cardstock/Cardboard, Paper Trimmer for Home Office School

Worked fine without instructions. Gorman Gray

I was a little hesitant to order this, since there were some negative comments about it, but it works much more easily than I expected. There's a YouTube video of someone using one of these (it seems to be this brand and model) and the user struggles mightily with it, so we expected to have to apply much more force to cut through a stack of paper, but that didn't turn out to be the case.Ours arrived with a slightly cracked safety shield, but it's only a cosmetic issue. The shield is fully functional.This is a great bargain compared to other paper cutters of this size and capacity.Update: I managed to break one of its bearings by abusing it. Bouncing with my full weight on the handle to cut through an oddly tough stack of paper is just a bit more than it was designed for. (Paper varies a great deal in its resistance to being cut. Only one large stack of over one thousand stacks I've cut gave me this much trouble. I should have divided it into smaller stacks.) Fortunately, Amazon carries the bearing (

I bought this as a companion to the Fujitsu ScanSnap iX500 in my newly declared war on paper. Here are my initial thoughts:1. It doesn't really come with instructions (one sheet on changing the blade). So it will take some trial and error to figure out all the settings if you've never used one (I hadn't). So start on some paper that doesn't have to be "perfect" when finished -- not your most beloved coffee table book. And even though I wiped it down, the first few cuts were oily, so beware.2. It's not all that precise. So if I had needed it for professional, square cuts -- I wouldn't be as happy. For this purpose - it's "close enough for government work."3. When unbinding a book, it does leave a nice clean edge that feeds fine through the scanner. And it does cut a large stack at once. Some tips: make sure you cut far enough in from the binding to get any glue that "squished" into the pages. It's easier to take off another millimeter or two than have to stop and manually reset misfeeds due to stuck pages. I also think it's nice to take the extra time to flip the pages and cut the outside edge down so the scanned margins are the same width on each side when scanned.4. This thing is big and heavy! I didn't really notice the ship weight, but if you're not scanning at least several banker's boxes full of books, it's probably not worth it in terms of weight/space trade off. I'm still trying to figure out where I'll store the darned thing.

I would not call this a professional guillotine. It is sufficient to cut small projects. I will be using it to cut books that I bound. They are only 100 sheets of paper, so it can cut them easily. The trick is getting the cutter tightened with the paper aligned correctly. This takes a bit of practice using this particular cutter. I found that stop arm, that looked like a windshield whipper to be hard to adjust and basically useless. You could spend more on a fancier cutter if you do a lot of work, this won't work for a busy 0rint shop. I got this for my personal use after my boss sold the Chandler Price we had at work. On the plus it is much smaller and I was able to set it on top of my antique sewing table.

Is so easy to use. It help me a lot with the finishing, and the price is excellet, This machine is a excellet product.

This guillotine is really nice and heavy, so no worries about it moving when you cut a stack of paper. Which is essential for clean book sides. I'm printing/publishing books, cutting off the edges to make them straight, and this cutter does a perfect job.I wanted a machine that I would not regret buying, it being kind of a toy, like some of the cheaper paper cutters. So I spent the money and got this one and I have been very satisfied. There are screws to adjust the pieces, should you need to. The usable parts are not set in stone, but adjustable.All in all, despite the fact that it weighs quite a bit to ship, it's been the hit machine for me.

Like others, I purchased this product in order to remove the binding from books. Thus far I've removed the bindings only from (pretty thick - 60+ page) magazines. This Gillotine slices through no problem. The tool is heavy duty. I have it on the floor and when the handle is raised it's like 3'.The black thing that repositions on the surface is made of rubber so once you tighten it, it isn't going anywhere. If you have a bunch of books the same size you can just position that thing where you want and you don't have to re-evaulate where you want the book everytime you put one in. The blade is sharp. I wiped it off with a paper towel due to the other reviews just to get the grease off. I haven't taken the device apart to see exactly how the long handle attaches to the unit that pushes the blade down. It does take a little bit of force to do the cut but nothing a 12 year old couldn't do.Literally all you have to do to start cutting is take the thing out of the box, screw one handle on (can be done by hand) and shove the long handle onto it's post. The smaller handle you just use to tighten your book or whatever against the surface so it doesn't go anywhere when you cut. Pair this up with a scanner containing a straight document feeder and you will have no problems converting all of your books to digital. For scanners you can do a kodak i1220 plus if you can find one used or get a scansnap.For the price you can't beat this. It was a great purchase!

First let me say this cutter is the 858 "Perfect/Stack Brand" S12 paper cutter that is sold else where. For some reason the branding that indicates the name isn't present but clearly the cutter is the same and even the flyer/instructions sheet that comes with it states the name as "Perfect A4 Stack Cutter" (A4 being letter sized). At first I thought it would be cheaper knock-off. But after handling it for a while I'm more certain that this was a unbranded over-produced run or possibly a quality control reject that kept it from being sold as a Perfect/Stack Brand, though it's possible that this is a return/remanufactured unit.First my biggest concern and the biggest bug bear. Alignment of the back guide fence. And just as I had suspected my unit was misaligned. I had accounted for this and knew I was probably going to have to do some minor modifications to realign it. Turns out all it takes is a 10mm wrench and some patience. If you turn the unit over on its side you can see the bolts that hold the guide fence. By loosening them and adjusting the fence ever so slightly you should be able to realign it. Note that its never going to be completely straight because the act of it being a manual loading cutter, but you can with time and patience you can get it to near perfect alignment that can satisfy your needs.Just as other people had stated there is a crap ton of grease EVERYWHERE. One of the first things you should do is bust out the paper towels and start cleaning it up. It's in every nook and cranny. I realize that the purpose of the grease is so that when in storage it doesn't rust, but the amount I removed was a bit in excess.I also found the draw of cutter handle seemed a bit stiff than was necessary. I'm a big guy but I can see if a smaller person could possibly having problems pulling down the handle. But for those that like a lighter draw you can open the side panel after removing the black thumb screws(2 on top, 2 on bottom) I was able to find the over tighte

This guillotine paper cutter met my expectations. It does an excellent job on heavy photo stock. I make note cards and other sorts of photo products and am happy with this cotter.

I bought this cutter for cutting books for Fujitsu Scansnap. I knew scanning is very fast, so I thought cutting books will be a bottle neck. But using this cutter, I can cut books very fast. Now I have so many cut books waiting for scanner to finish scanning. Must buy for scanning books.