Customer Reviews for VEVOR Welding Table 36 x 24-inch, 600LBS Load Capacity Steel Welding Workbench Table on Wheels, Portable Work Bench with Double-Layer Storage Board, 5/8-inch Fixture Holes, 11 Hooks

I love my new little rolls table. If you are on rhe fence about buying it, get it. PROS Sturdy Rolls nicely Well thought out design CONS Holes in the table top are a bit large and the spacing didn't work for me The feet to convert it into a stationary table are threaded and difficult to operate

First off, For sake of complete transparency, I can’t give a completely accurate review on this welding table because I didn’t use it as intended… I just needed the table top. And this seemed like a great deal since this entire table was less expensive than the materials alone Just to make something similar to this. what I can say is that the item came in fast and exactly as described, was cheaper than anything else similar that I could find, and worked perfectly for my use. I even ended up recycling the legs to use as reinforcements for a different table of mine. Overall this table was definitely worth what I paid for it and I would recommend it to anyone looking for a small welding table.

once again, unbelievable value for the money, this is a legit welding table the top is thicker than I thought it would be for this money, Great Job Vevor!!!!!

Functional low cost product.

Table Showed up within 2 days, super simple to put together. i have had a great time putting my ground clamp on and welding anything i ever need comes with 4 clamps, positioners, gloves, brass brush, and a slag hammer.

Sure it's not a certi-flat. Bit it's also not 700 bucks! For the price it's great! Been absolutely perfect in my shop to give me the extra workspace I needed!

This was the cheapest I found. The bolts are not great quality. I was able to use all the bolts but one. I had spare bolts around so used that but it would be a good idea to replace them all with better quality bolts. I could see the wheels themselves giving out at some point if too much weight is put on it. I didn't replace anything but that one bolt. It's a good table for a hobbyists welder and at an affordable price.

These are pretty great tables.. the only thing i can say is that the hardware included is small and needs to be replaced. I knew about this prior to ordering cause of the reviews. But otherwise a great little table

ok

First off, these are good tables for the price and I would recommend them. I bought 4 of these. Here is what I found.Pros:1. Decent paint job on the blue areas. I feel like it will hold up well. Raw metal on top.2. Sturdy but .... (see cons)3. I like the adjustable tray down below.4. Its metal top is easy to ground your work on.5. Easy to assemble6. It's a table, it tables well.Cons:1. Sturdy...but I doubt it will hold the weight it describes in the description. But if you are looking to put a half ton + on a $100 table made in china, you need to have your head examined. I feel 500 lbs is the limit of comfortable here.2. The failure point is going to be on the legs where the casters attach. There is a small square of metal tacked (not fully welded) at the bottom of the leg in 3 or 4 locations. The welds are small and spatter is everywhere.3. Spatter prevented casters from seating properly on 25% of the legs across the 4 that I purchased. A quick tap with a hammer and cold chisel popped the spatter off but left a tiny area exposed for rust.4. Casters are ok for plastic casters. However the locking mechanism doesn't do a sufficient job of preventing the caster from rolling. Left me chasing my table with a flap disc on an angle grinder a few times.5. One of the 4 tables I purchased had an extra nut but missing washer. Not a big deal.6. Too small and too few washers in my opinion. Flat washers are provided for each bolt (1 per bolt but you need 2. One for bolt and 1 for nut). the heads of the bolts are uncomfortably close in size to the holes. If you go gorilla on the bolts, I feel you could pull it through the holes on the legs. Spend 50 cents and throw a few more washers on there. You will need 8 extra.7. Packaging is a box. That's it. One of the 4 I purchased had the center tray edge slightly bent during shipping since there is nary a styrofoam pad to be found. A few whacks with a soft mallet fixed it right up though.I know all that sounds bad, but really it's a good